Видео

Thanks! Do hinges need to be labeled?

SDI's your white paper "the Risk of Grouting Steel Frames" also says grouting is usually not necessary for masonry construction. However if done properly it will not cause any issues w/ the frame. But when not coordinated properly a thin slurry is often used & that excess water often causes rust.

What is the name of laboratories can handle this kind of tests?

This is nice but I want to retrofit my house with a steel framed door but it has wooden 2x4 studs. Where can I find that video?

I also put my level up to the screen to make sure it was level, plum, and square, head neck and chest !!!! ☠

Nice video, but not exactly what I need

Umm I don't think I've ever seen a mason install door frames

Why do firefighters breach these doors like it's nothing?

Quisiera saber más

I need one of these for my room

I'm here because I am watching a video on ethical hacking, and Apple came out with BlastDoor, to make sure that jailbreaks are extremely difficult to do, which they have been rare now. Lol

What an arduous, complicated, and expensive process.

Anyone know how to remove one of these frames from an old house?

If the contractor finish the mason block first, how to install the bracket that set on the floor??

That bubble has to be in the middle of the two lines.

Thank you.

I wonder if this works? Let’s fucking explode it to make sure

can you tell me how to hang a door on a homemade pallet shed( i have zero carpentry skills 😂i have come this far and dont want to give up thanks kindly 😊

4:10

This is just what I needed thank you. I had a terrible carpenter install my back door, the gap on the hinge side was none existent while on the other side the gap was over a quarter inch and bugs where getting in from it.

What if a corner is separated

que pasa si la visagra esta soldada

I gotta reverse engineer a door so thanks for the hardware run down.

这种安装方式，太老旧了！

NARRA RENE BALDO ??

Great video

We've been welding all of our masonry frames over the last few months instead of ordering them custom. Is there some sort of jig made to keep the legs 90 degrees to the head? I made a jig out of wood the frame sits on but if I had something more sturdy, that'd be great.

Me dejaron la puerta muy arriba y tengo un espacio de dos centímetros por debajo, o sea se escucha todo lo que se habla del otro lado de la puerta

Very informative as I’m dealing with this situation

Are we really using a plumb bob?

Put the hardware side of the frame flush to the wall face. Not centered in the block. So door can open to 180 degrees to the wall.

EXCELLENT thank you

This is a great example of how you are supposed to install a metal door frame but fails to show how long before you replace said frame. Yes installation makes sense and is right, but I have to replace these steal frames and doors, because they rust.

It's hollow! You forgot to fill with cement?😮

Hit your door in the same spot and show proof of speed. Y’all are scumbags stealing from people with this BS

Cuánto cobrar por hacer esa intalacio'n?

Can you dig deeper into explaining NFP 80 and include why 252 and UL are on the label, not NFP 80?

Good stuff I wish guys would watch and learn this stuff.

So Cool 😎

A mí puerta la dejaron mal se levanta una punta arriba del lado del picaporte y no cierra bien .como lo puedo solucionar ?

I got two words. Fuck all that bullshit.

I appreciate your video. Thanks 🙏 have learnt a lot

Whats a PLS

Thank you 🙏

El marco quedó hueco en la parte interior …..? No le rrellenaron con cemento el marco …….

Donde puedo comprar este tipo de marco metálico en mexicali?

Demasiado detalle es complicarse la vida con algo tan simple como alinear un marco

Comically stupid video. Why would you show this being installed on obsolete cinderblock, that no ine had used for decades....

You failed to mention that you should also check that the door frame is on the same plane by cross stringing before drywall. Especially and certainly on double door openings. String should touch where they cross. If not, the frame is out of alignment and needs to be adjusted.

My door way that the seller built it not correctly framed I need to know how to fix the frame cuz the door won't even close etc